devid

Removing a toilet can seem a bit difficult job to most people. But, it is not. Most people can manage to remove the toilet on their own without any professional help. All you have to do is to make sure to follow this tutorial properly and you will be good to go. Check out this guide to know how to remove a toilet.

Always keep in mind that if there is a ceramic toilet, it can be heavy. So, avoid lifting it on your back, it can lead to injuries. Make sure to lift it on the legs. Moreover, if available, you can take help from somebody else.

Requirements

Before you proceed with the process, check out what you need.

Tools:

sponges
Screwdrivers
Lids and paint buckets
Wire brushes
Air ratchet wrenches
Wrenches

Material:

Cleaning rags
Two-piece toilet

Steps to Remove a Toilet

Here are some steps which guide you on how to remove a toilet-

Step 1: Disconnecting Toilet Connector

The very first thing that you will have to do is to drain the water completely from the toilet. No matter if you are removing the toilet, or replacing it, you need to first drain the water. For this, follow the steps mentioned below.

To start with, you will have to disable the power supply at your shut-off valve. Usually, it is present on the wall at the back of the toilet, but, it can also be present on the floor.
Next, you will have to flush the toilet multiple times to drain the water completely. The flushing toilet should be beautifully designed to look fine for your guests.
Now, you may have to use the sponge to dry it completely and remove the remaining water.
After this, simply disconnect the connection tube. You will also have to make sure to keep a towel or a bucket near you so that you can collect the water standing in the drain.
When you are done with this, you will have to simply disconnect the connector at the tank also.

Step 2: Removing the Tank

Now, if you use a two-piece toilet, you must remove the toilet tank separately. Otherwise, for the one-piece toilet, you can skip this step and move to remove the toilet bowl. For this, follow the steps mentioned below.

First, you need to know that tank is attached using mounting bolts. You can find the mounting bolts placed on the sides and the middle sometimes.
You will then have to use a basin wrench or the ratchet wrench to loosen the nuts and remove them.
Next, you will have to lift the toilet tank and remove it. Make sure to place it in a location where it will be safe and out of your way.

Step 3: Remove the Toilet From the Floor

Now, the next step to removing the toilet is to unbolt it from the floor. For this, follow the steps mentioned below.

To start with, if you feel necessary, you will have to pry off the caps with the help of a screwdriver.
Now, you will have to use an adjustable wrench and remove the nuts. There are chances that you will be able to remove the screw using your hands.
Next, if you see that the screws are jammed completely, you can use penetrating oil and spray it to loosen the nuts.
In case the penetrating oil does not help, you will have to make sure that you use a hacksaw and cut bolts. You can also split them with the help of a nut splitter.

Step 4: Breaking the Toilet Seal

Now, the next step to removing the toilet is to break the seal. The toilet wax ring will seal the toilet flange and the toilet bowl’s bottom to the floor. So, if you wish to remove a toilet, you will have to break the seal. For this, follow the steps mentioned below.

Bestride the toilet and then try breaking the seal gently.
You will then have to raise the toilet bowl and safely place it on the towel so it won’t come in the wait. You may not be able to carry out this alone, so, you will need a partner.

Step 5: Pull Out the Wax Ring

You will now have to pull the old wax ring. Follow the below-mentioned steps to do this.

First, you need to get a scrapper. You will have to use a scraper and try to pull out the wax from the flange and also, the bottom.
Next, throw the wax that you have pulled out and make sure to throw it properly so that it does not stick anywhere else.
The next thing that you need to do is to cleanse the flange.
Also, if you want to check the toilet flange, you can do it at this moment. If it needs to be replaced, you can replace the toilet flange now.

Step 6: Enclose the Hole

This is the last step in how to remove a toilet process. Now that you have removed the toilet, you need to enclose the hole and then dispose of the new one. For this, follow the steps mentioned below.

You will have to stuff a cloth or a rag in the hole. This is a must so that the sewer gas does not seep into your house.
Next, you can use a bucket to enclose the rag and the flange.

To dispose of the old toilet, you will get two different options:

The first thing that you can do is to call the local trash services in your area and then ask them to pick up the old toilet. You can also visit their website to connect with them. In this case, you will have to dispose of the non-ceramic part individually.
Next, you can also visit the landfill and dispose of the toilet.
Other than this, you can also call the local recycling centers and check if they can take the non-ceramic parts. For this, you can also seek help from the water authority of your area so that they could suggest something.
Moreover, you can also contact the charity in your area which will accept and reuse the building materials donated to. But, make sure to donate only if it is in working condition. If they accept they may be able to arrange the transportation also.

Winding Up

So, we hope that by the end of the post, you have learned to remove the toilet. Now, you can also install a toilet if you want or can make the required changes in the bathroom if you wish. In case you are still not able to learn the process, we will advise you to contact a professional. Stay tuned to us for more such posts.

FAQs

How to remove a toilet seat?

You can easily remove a toilet seat. What you all need to do is first unscrew the bolts. If it is badly rusted and tight then you must use lubricant and then try to unscrew it.

How to remove rust from a toilet bowl?

Try a homemade cleaning solution to remove rust from the toilet seat. Do not use bleach as it can make it worse.

How much does it cost to remove a toilet?

Removing toilet seat cost depends on what type of toilet you are using. Also, what plumber you are calling for it?

Running a toilet is one of the issues that you need to fix as soon as possible. People usually do not know how to resolve this issue and may get stuck in the issue. But, fortunately, fixing the running toilet is easier than you imagine. There are straightforward methods that you can use to fix the running toilet issue. If you are also facing a running toilet issue, check out this post. Here are some quick fixes to resolve the issue.

Reasons that You Face Toilet Keeps Running Issue

You may have to adjust the height of the float.
There may be some issue with the flapper and you have to replace it.
There is a need to shorten the length of the refill tube.

Tools Required

Replacement Fill Valve.
Cutting pliers. Rubber gloves.
Toilet replacement parts.
Multi-bit screwdriver.

How to Fix a Running Toilet

Here are some methods which help you get rid of runny toilets-

Method 1: Address the Problems with Flapper

One of the common reasons for facing a running toilet situation is issues with your flapper. It is a rubber seal that prevents the water from draining and stays in the bucket only. Whenever you flush the toilet, the chain present will pull up the water and the freshwater will fill up the bowl. To address and resolve the flapper issues, follow the steps mentioned below.

The very first thing that you need to do is to turn off the water supply to the toilet.
After this, you will have to use a towel and lay it out of your way. You can also place it in the corner. You will now have to hold any end of the lid of the toilet and pull the lid off.
Next, you will have to place the lid on the towel that you have led. They can be broken easily so make sure to keep them in a safer place.
Now, you will have to check the chain which pulls up the flapper. You may face the issue if the chain is short or long than needed.
In case you notice that the tension is high on that chain, you will have to detach the hook and attach it at least two links above. It will help to loosen the chain and then you need to attach the hook and the lever.
Other than this, if the chain is long, you will have to trim the chain to make it an appropriate size. After this, you will have to attach the hook to the flush lever again.
Now, the next thing that you will have to do is to check the flapper. For this, you need to detach the flapper. Check if the open tube is present in the center. You will now have to check the flapper if there is any disintegration, discoloration, or mineral deposits.
In case there is a mineral deposit, you will have to make sure to clean it. To do this, you can use vinegar. You will have to soak the flapper in vinegar for 30 minutes and then use a toothbrush to clean up all the dirt and buildup.
When this is done, you will have to place the flapper back and attach all the pins.
Now, you need to run the water again and listen to the sound. You can then check if the issue is resolved or not.
Other than this, if you see that the flapper fails to seal properly even after cleaning, you need to buy a new one. Make sure to buy the same style of the flapper and fit it into the toilet.
For this, you need to place it properly and then fit all the nuts.
Now, turn on the water and then make sure that the issue is resolved.

You may also read- Most Powerful Flushing Toilet For Clean and Fresh Bathroom

Method 2: Checking the Fill Valve

In case you are not able to fix the running toilet issue by changing the flapper, there is a high chance that the issue is with the fill valve. You will then have to check if there is any leak and then place a new one. The process is further divided. You need to follow the steps in the same sequence to avoid errors.

Checking the Fill Valve

To check the fill valve, you will have to flush your toilet and check if there is any leak.
Next, you will have to lift the toilet float to check if there is any stoppage of water,
You may have to adjust the float arm to prevent the tank from filling. Go it when the water level in the tank is just 1 inch below your overflowed pipe.
Next, if you still notice the leak, you may have to replace the fill valve.

Replacing the Fill Valve

For this, you need to disable the water supply temporarily. Now, you need to flush the whole water and use a sponge to remove the remaining in the tank.
When done, you will have to disconnect the supply line of water and then loosen the fill valve locknut. You will now have to lift and remove the old fill valve.

Installing New Fill Valve

Now, you will have to place the new fill valve in the correct location. For this, you can also use the manual. Tighten all the nuts.
Next, you need to adjust the fill valve according to the height. In case you notice that the fill valve is placed at the maximum height, still, the overflow pipe is upper than the critical mark, you will have to use a hacksaw and shorten it. It should be at least 1 inch below the critical mark.

Connecting Fill Tube

To start with, you will have to take one end of the newly installed fill tube and then attach it to the fill valve nipple. You will then have to attach the other end to the angle adapter.
Next, you will have to clip the adapter to the overflow pipe
When done, you will have to attach the flapper to the lever and then turn on the water. Check if the issue is resolved or not.

Also, know about it- 11 Best Low Flow Toilets To Save More Water In Toilet

Method 3: Adjust the Water Level

Another reason for which you can face the running toilet issue is the water level. If the water level is high, the water will keep draining into the tube. So, to fix this issue, you need to adjust the water level. For this, follow the steps mentioned below.

Checking the Level of Water

The first thing that you have to do is to check the overflow tube. In case you are not aware of what it is, it is a tube present in the center of the tank. It will connect the toilet bowl and tank.
Next, you will have to check if the water is draining into the tube. In case it happens, you need to adjust the level of water by moving the float lower.

Check the Kind of Float Present

You are going to get two types of float presents. One is a float ball fill valve and the other is a float cup fill valve.
If you notice a ball-shaped float at the end of the arm attached to the fill valve, it means that you are dealing with the float ball fill valve. In this case, you need to check the ball. If there is water inside it, you will have to replace it.
Other than this, if there is a small cylinder around the fill valve, it means there is a float cup fill valve present. The cup moves up and down on the shaft and with its height, you can determine the water level.

Adjust Float Ball Fill Valve

Now, if you have the float ball fill valve, you will have to look for the screw with which the float arm is attached to the fill valve. By turning this screw, you will be able to adjust the height, you can use comfortable height toilets for your own comfort.
You will have to flush and then again fill the tank. You will now have to check the water level.
Now, you need to make sure that the water level is 1.5 inches below your overflow tube. If it is not, you will have to keep moving the screw to adjust the level of water.

Adjust Float Cup Fill Valve

For the Float cup fill valve, you will have to adjust the water level in the same way. look for the adjustment screw; to adjust the water level, you will have to turn the water level.
Next, you will have to flush and fill the tank again.
You will now have to check the water level.
Now, you need to make sure that the water level is 1.5 inches below your overflow tube. If it is not, you will have to keep moving the screw to adjust the level of water.

Verify the Fill Tube

Now, the last step in the process to fix the running toilet is to check if there is an issue with the fill tube. It is the tube that attaches to the fill valve and fills the water tank after you have flushed it. Make sure that this tube is above the waterline. If not, the running toilet issue can occur. So, when you will fill the water tank, you will have to check that the tube must not in the water. If it is under the waterline, you will have to trim the tube enough so that the tube is above.

To Wind Up

All the methods mentioned above are doable and you will be able to resolve the toilet that keeps running issue easily. If you still get stuck at any point, we will suggest you call a plumber.

FAQs

How to fix a running toilet without a ball float?

First, Replace the fill valve only if the tank is overflowing. If this doesn’t work out then try to replace the toilet flapper.

Cost to fix a running toilet?

The average cost can range between 60 to 200 dollars. It depends on what type of problem you are facing.

How to Remove a Toilet On Your Own [Step-by-Step]

Requirements